Indicate the cost or deduction for the below listed options.
Price should include all required options and special equipment.
Option 9A.
Automatic transmission power take-off provision
Option 9B.
2 Full-length cab steps or running boards. (Per set - One on driver's side, one on passenger side)
Option 9C.
Standard gasoline engine with the highest cooling capacity in lieu of diesel engine - DEDUCT (State size and horsepower)
Option 9D.
Additional set of keys (Ignition and door locks)
Option 9E.
Auxiliary Upfitter Switches
Option 9F.
Mounted 11' platform body meeting Specification E1320DRW.
Option 9G.
Mounted 11' aluminum platform body comparable to Specification E1320DRW. (Minimum 1 1/4" aluminum extruded floor instead of steel)
Option 9H.
Mounted 11' platform dump body meeting Specification E1327.
Option 91.
Mounted 11' aluminum platform dump body comparable to Specification E1327. (Minimum 1 1/4" aluminum extruded floor instead of steel)
Option 9J.
Permanently installed bulkhead to fit truck application (Minimum requirement to top of cab) EACH $
Option 9K.
Provide live hydraulics with under hood clutch pump. Pump shall be cast iron design capable of 3500 PSI; aluminum pumps will not be accepted. Reservoir shall be 7 gallons with filtered breather cap, suction strainer, sight gauge and in tank return filter rated to 25 GPM. Valve shall be cable operated. Control valve must have a main relief and a relief for the hoist down function. This shall control the hoist only.
Option 9L.
Provide hydraulics and controls 12VDC activated for dump hoist only.
Option 9M.
Mounted standard utility tool body
Acceptable makes and models are:
- Knapheide 6132D54
- Stahl CHALLENGER 132VVD-54
- Reading CLASSIC II
- Omaha 132D54V
- RKI L84DW94
- Dakota SB (Service Body)
Equivalents accepted if pre-approved at least 5 working days before bid opening. Pre-approval may require presentation of a demo for review.
Body to include flush mounted LED tail, stop, turn, backup and clearance lights as required per FMVSS 108 standards. Unit must include a step bumper with some type of surface designed for safety (tread plate, Galva Grip, etc.) with pintle hook recess.
Option 9N.
Mounted standard aluminum utility tool body comparable to steel units.
Acceptable makes and models are:
Equivalents accepted if pre-approved at least 5 working days before bid opening. Pre-approval may require presentation of a demo for review.
Body to include flush mounted LED tail, stop, turn, backup and clearance lights as required per FMVSS 108 standards. Unit must include a step bumper with some type of surface designed for safety (tread plate, Galva Grip, etc.) with pintle hook recess.
Option 90.
C-Tech drawer unit (or equivalent) containing 6 full width compartments; (3)-3" depth drawers, (2)- 5" depth drawers, and (1)- 7" depth drawer. Unit to contain 1 set of drawer dividers.
Option 9P.
C-Tech drawer unit (or equivalent) containing 2 full width compartments; (2)-3" depth drawers. Unit to contain 1 set of drawer dividers.
Option 9Q.
Flip top for Utility Body: Top of compartment opens for storage. Can be either side or both sides. Telescopic roof and crane mounting kit will impact flip top application. Latch is located in center horizontal compartment.
Option 9R.
Minimum 25" high panel extension cover with minimum 42" locking rear doors which will provide a minimum 48" interior height for storage and work area (Canopy roof style).
Option 9S.
Body to have 3 sections, tempered steel telescopic sliding roof and two-piece, rigid aluminum, end gate cover to protect cargo area from weather and theft. A mechanical type seal will be placed on the telescopic sliding roof and end gate cover.
Option 9T.
Raise Telescopic Roof to get 36" clearance for the above option
Option 9U.
Crane mount reinforced rigidly while maintaining full compartment space on top rear corner of body either left or right for a 3500 lbs. cap. crane (with no mounting holes or bolt holes, we will drill to suit ourselves)
Option 9V.
One - double bottle gas drop well with minimum 55" clearance height (for large Bottle use) and retainers in lieu of the interior 48" full height vertical compartment.
Option 9W.
Commercial grade spray on bed lining to be applied in the cargo area of the utility body, to include floor, sides tailgate, front, and horizontal surface of bumper.
Option 9X.
Heavy duty, Class V (2-1/2" square tube) receiver trailer hitch. Includes an adapter to reduce to 2" (Class III/IV), seven-wire RV style trailer plug and electric trailer brake controller.
