Indicate the cost or deduction for the below listed options.
Price should include all required options and special equipment.
Option 7A.
Automatic transmission power take-off provision
Option 7B.
2 Full length cab steps or running boards. (Per set - One on driver's side, one on passenger side.)
Option 7C.
Standard gasoline engine in lieu of diesel engine with the highest cooling capacity DEDUCT (State size and horsepower).
Option 7D.
Additional set of keys (Ignition and door locks)
Option 7E.
Auxiliary Upfitter Switches
Option 7F.
Mounted 9' platform body meeting Specification E1320DRW
Option 7G.
Mounted aluminum 9' platform body comparable to Specification E1320DRW (Minimum 1 1/4" aluminum extruded floor instead of steel)
Option 7H.
Mounted 9' platform dump body meeting Specification E1327
Option 7I.
Mounted aluminum 9' platform dump body comparable to Specification E1327
(Minimum 1 1/4" aluminum extruded floor instead of steel)
Option 7J.
Mounted 9' dump body comparable to Specification E1335
Option 7L.
Permanently installed bulkhead to fit truck application (Minimum requirement to top of cab)
Option 7M.
Provide live hydraulics with under hood clutch pump. Pump shall be cast iron design capable of 3500 PSI; aluminum pumps will not be accepted. Reservoir shall be 7 gallons with filtered breather cap, suction strainer, sight gauge and in tank return filter rated to 25 GPM. Valve shall be cable operated. Control valve must have a main relief and a relief for the hoist down function. This shall control the hoist only.
Option 7N.
Provide hydraulics and controls 12VDC activated for dump hoist only
Option 7O.
Mounted standard utility tool body
Acceptable makes and models are:
- Knapheide 6108D54
- Reading CLASSIC II
- Omaha 108D54V
- Stahl CHALLENGER II 108VVD-54
- RKI L60DW94
- Dakota SB (Service Body)
Equivalents accepted if pre-approved at least 5 working days before bid opening. Pre-approval may require presentation of a demo for review.
Body to include flush mounted LED tail, stop, turn, backup and clearance lights as required per FMVSS 108 standards. Unit must include a step bumper with some type of surface designed for safety (tread plate, Galva Grip, etc.) with pintle hook recess.
Option 7P.
Provide hydraulics and controls 12VDC activated for dump hoist only
Mounted standard aluminum utility tool body comparable to steel units.
Acceptable makes and models are:
Equivalents accepted if pre-approved at least 5 working days before bid opening. Pre-approval may require presentation of a demo for review.
Body to include flush mounted LED tail, stop, turn, backup and clearance lights as required per FMVSS 108 standards. Unit must include a step bumper with some type of surface designed for safety (tread plate, Galva Grip, etc.) with pintle hook recess.
Option 7Q.
C-Tech drawer unit (or equivalent) containing 6 full width compartments; (3)-3" depth drawers, (2)- 5" depth drawers, and (1)-7" depth drawer. Unit to contain 1 set of drawer dividers.
Option 7R.
C-Tech drawer unit (or equivalent) containing 2 full width compartments; (2)-3" depth drawers. Unit to contain 1 set of drawer dividers.
Option 7S.
Flip top for Utility Body: Top of compartment opens for storage. Can be either side or both sides. Telescopic roof and crane mounting kit will impact flip top application. Latch is located in center horizontal compartment.
Option 7T.
One - double bottle gas drop well and retainers in lieu of three shelves and dividers in one of the full height vertical compartments, maintaining an interior height of 48".
Option 7U.
Minimum 25" high panel extension cover with minimum 42" locking rear doors which will provide a minimum 48" interior height for storage and work area (Canopy Roof Style).
Option 7V.
Body to have 3 section, tempered steel telescopic sliding roof and two-piece, rigid aluminum, end gate cover to protect cargo area from weather and theft. A mechanical type seal will be placed on the telescopic sliding roof and end gate cover.
Option 7W.
Raise Telescopic Roof to get 36" clearance for the above option.
Option 7X.
Crane mount reinforced rigidly while maintaining full compartment space on top rear corner of body either left or right for a 3500 lbs. cap. crane (with no mounting holes or bolt holes, we will drill to suit ourselves).
Option 7Y.
Commercial grade spray on bed lining to be applied in the cargo area of the utility body, to include floor, sides tailgate, front, and horizontal surface of bumper.
Option 7Z.
Heavy-duty, Class V (2-1/2" square tube) receiver trailer hitch. Includes an adapter to reduce to 2" (Class III/IV), seven-wire RV style trailer plug and electric trailer brake controller.
